COMBIVIS Programming Software_S6 Servo Drive Startup

KEB S6 Servo Drive – Start-up procedure

Starting a Motor in 10 Steps

This is how to quickly and effectively start-up a servo motor using our S6-K drive. Utilizing the programming Wizards in KEB’s COMBIVIS 6 software, we can break down the process into 10 simple steps.

In this blog post specifically, we will be highlighting the startup of a KEB Dynamic Line III servo motor utilizing closed-loop control with encoder feedback.  The general process will be similar for other motor types.

What do I need to get started?

Closed-loop control with encoder feedback is a VFD control method that utilizes measured speed feedback through an encoder device.

In general, there are (5) main components that will be required to startup your particular motor. 

  1. Power Source (S6 has options for 1-phase and 3-phase input)
  2. S6 Servo Drive
  3. 3-phase AC motor (S6 runs either induction or servo motors)
  4. Encoder feedback device and encoder cable
  5. Combivis programming software to configure VFD

Once we connect our power and devices in their respective manner, we can startup COMBIVIS 6 and soon begin programming.

Getting Connected to COMBIVIS 6

Open a new project in COMBIVIS 6 Software: Click the Scan for Device Icon

Before we can start programming, we first need to connect our drive to COMBIVIS 6 using the KEB USB-to-serial converter. We can then perform a device scan and add the S6-K drive to the COMBIVIS 6 project.

Click the Start Search button to find the KEB S6 Servo Drive

Once the S6-K has been connected to the project, we can open the interactive programming Wizards that are specially designed into the COMBIVIS 6 software for use with generation 6 VFDs (S6, F6, H6).

Once found, you can add the device to your project

Now we can take a look at the start-up Wizards Tabs to get your motor spinning.

The wizards tabs in the KEB COMBIVIS 6 software

Now that all of our components are wired-up and connected, we can now dive into our 10 start-up steps.

The 10 Steps to Starting a Motor

Step 1: Restore factory default device settings

Major Tab: Basic settings

Minor Tab: Basic settings

First, restore the device to factory settings

The first tab we will visit is the Basic settings tab. In this tab, the option we will want to choose is “Reset device to defaults”. This selection will clear any programming currently in the drive and restore the drive to its factory settings. New drives will ship from KEB with default settings but it is always a good idea to do this step in order to ensure you are starting with the defaults.

After the drive resets, we will move into the Motor Tab.

Step 2: Input motor nameplate data

Major Tab: Motor

Minor Tab: Motor data

Input the motor data in the “Motor” tab

Inside the Motor tab, this is where we will input our motor rated nameplate data. In the case of a KEB motor, we can utilize the KEB motor database to easily load the rated nameplate data. We will input our KEB motor part number into the database, which will automatically load the motor data. We can then confirm the motor type and the type plate data below. If you are using a non-KEB motor, simply select the “Manual input” button on the right, and input the rated data of your specific motor in the spaces below.

Next, if your motor has a brake, we will briefly jump into the Brake control tab.

Step 3: Activate brake control

Major Tab: Motor

Minor Tab: Brake control

Activate the brake control tab if applicable

In the Brake control tab, we want to ensure that “Activate brake control” is selected so that we may operate the motor brake using the VFD/drive. In this tab, we can also set our brake release/open and engage/close times, if applicable. We will keep the brake control source as “controlword” so we can control the brake for the motor identification and test run.

Now we will enter into the Feedback mode tab.

Step 4: Select closed-loop control mode and speed control source

Major Tab: Feedback mode

Minor Tab: Wizard

Select the feedback mode you are using

In the Feedback mode tab, we will set the control mode to “Encoder with motor model”; this is the control mode for closed-loop with encoder feedback. You may also see V/f mode and Encoderless (SCL) options. These are other available control modes that may require additional or different programming than what we are working with here.

We will set both speed control source and position control source to “Encoder A”.

Step 5: Set applicable encoder type

Major Tab: Feedback mode

Minor Tab: Wizard

Select the encoder type you’re using

Expanding the “Encoder A” drop-down menu will expose an encoder type selection. Since we input the KEB servo motor part number in the Motor tab, the Resolver encoder type is already populated. This section is where you would select your encoder type and enter the Encoder mounting position, if known. If the mounting position is unknown, this can be calculated during the motor identification.

Next we will quickly move to the Controller tab.

Step 6: Set motor inertia and load inertia, if known

Major Tab: Controller tab

Minor Tab: Speed controller


Set motor inertia and load inertia, if known

For the Controller tab, the only parameter to adjust at this time would be the motor and load inertia, if known. The motor inertia would be a parameter obtainable from your motor manufacturer, and in the case of our KEB motor, it is auto populated from the KEB part number.

We are now ready to enter the Identification tab.

Step 7: Perform motor identification and detection of encoder mounting position

Major Tab: Identification tab

Minor Tab: Wizard

Identify the motor and the encoder mounting position

We start in the Identification tab by confirming our rated nameplate data. Once confirmed, a second box appears and offers added detection options for the identification.

Identification Step 2 – EMF Detection

This is where we can select to detect the encoder mounting position. In the third box, there are (4) requirements that must be fulfilled to allow for motor rotation and identification; STO digital inputs, voltage supply, no error state, and brake released.

Once these (4) requirements are met, we can begin our identification, which will cause the motor to rotate. The identification must be performed under no-load conditions.

Old and New Values will populate after the motor identification

During and after the motor identification, a small table will populate with a few motor parameters and the encoder mounting position, and their respective “old” and “new” values. The “old” and “new” values represent the parameter value before and after the identification. Some parameters might be different after the identification, but this is expected as the identification now incorporates cabling and other realistic setup characteristics.

Confirm the identified parameters

We can confirm the identified parameters and then move into the Modes of operation tab.

Step 8: Select “Velocity Mode”

Major Tab: Modes of operation

Minor Tab: Wizard

For this demo we’ll use Velocity Mode

You will see (5) available modes of operation for this S6 drive. For our testing, we will choose “Velocity mode.”

Step 9: Choose ramp mode and speed limit settings

Major Tab: Velocity mode pop-up

Minor Tab: Ramp mode and Speed limit settings

Once you select “Velocity mode”, a Velocity mode pop-up will appear. The ramp mode tab is where you can select between S-curve and linear ramp profiles. In the Speed limit settings tab, you can set your maximum and minimum velocities in each rotation direction.

Select “S-Curve”

When you select your speeds, click the “X” at the top of the Velocity mode pop-up.

Select the speed you want to run the motor

We are now ready to test run the motor.

Step 10: Perform Test Run

Major Tab: Test run

Minor Tab: Start ‘test run’ wizard

In the “Test Run” tab click “Start ‘test run’ wizard”

Click on the Test run tab and an available “Start ‘test run’ wizard” option will appear. Clicking on the “Start ‘test run’ wizard” will pull up the test run wizard window.

Set the target velocity of your servo motor

At the top of the test run wizard are the (4) preconditions for successful running, which were the same prerequisites for the motor identification. Once the (4) conditions are met, we can set a target velocity using the “Velocity 1” input near the bottom. The slider bar represents the maximum forward and reverse speeds you created in the Velocity mode tab.

After you set target velocity, click the start button to move the motor

Once a speed is in the “Velocity 1” text box, it can be loaded into the drive using the “Set target velocity” button. Click “Start” when you are ready to spin the motor. The motor will spin and the encoder speed will be tracked on the speedometer.

Stop the motor by clicking the Stop button

Conclusion

You have now quickly and effectively started a motor with an S6 Servo Drive.

You may have noticed that we skipped over some tabs in the COMBIVIS 6 Wizards, such as Protection / Warnings, Fieldbus, and other Controller tab parameters. These are important tabs that you would visit to complete the commissioning of your drive and motor for successful integration into your industrial machine.

If you are interested in visiting with KEB sales or engineering regarding your new application, please contact us using the form below.

Interested in KEB’s automation technology? Contact a KEB engineer today to discuss your application.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Contact
  • This field is for validation purposes and should be left unchanged.